Combo-CN134 CCL 105 EPABX with Beetel C51 Phones – Setup Guide

Setup guide · Combo-CN134

Wire the CCL 105 EPABX and 5 Beetel C51 caller ID phones: 1 outside line shared by 5 extensions, with free internal calls.

CCL 105 EPABX with Beetel C51 caller ID phones

What’s in the box

  • 1 × CCL 105 EPABX system
  • 5 × Beetel C51 caller ID phones
Telephone cable, rosettes and MDF box are not included.

Tools you’ll need

  • 2-core telephone cable
  • A rosette (phone socket) for each phone
  • Screwdriver and wall plugs
  • Cable clips or conduit
  • Labels or a marker
  • MDF box if you have 8 or more phones

Install

  1. Mount the unit.Fix the CCL 105 on a dry, ventilated indoor wall near the telephone line socket and a power point.
  2. Cable each phone.Run 2-core telephone cable from the unit to each phone point. Keep it 30 cm away from mains wiring.
  3. Label both ends.Mark each cable with the extension it serves.
  4. Fit rosettes.Terminate each cable on a rosette at the phone end.
  5. Connect the outside line.Connect your landline to the LINE / CO port.
  6. Connect extensions.Connect each extension cable to an EXT port.
  7. Plug in the phones.Connect a Beetel C51 to each rosette.
  8. Power on and test.Call from one extension to another, then make and receive an outside call.
Power-backup options are model-specific. Do not connect a battery unless the manual for your exact model shows a supported battery input and voltage.

First-time setup

Programme the system

  1. Find the extension numbers and programming codes in the CCL manual for your model.
  2. Set extension numbers, call restrictions and day / night mode as needed.
  3. Test call transfer, hold and call pickup from each phone.
Caller ID on the C51 phones needs caller ID service on your outside line. Ask your telephone provider if numbers do not show.

Daily use

  1. Dial an extension number to call another phone free.
  2. Answer outside calls on the phones set to ring, or use call pickup from another extension (see the manual).
  3. Transfer or hold a call using the steps in the manual.
  4. Works as an internal intercom even with no outside line connected.

Troubleshooting

Problem Try this
No dial tone on one phone Check its cable, rosette and EXT port. Swap the phone with a working one to test.
No dial tone on any phone Check the EPABX power. Make sure the unit is switched on.
Cannot call outside Plug a phone directly into the landline socket. If there is no tone, the fault is with the line provider.
Caller ID not showing Ask your provider to enable caller ID on the line. Check the setting in the EPABX manual.
Crackle or hum Move cables away from mains wiring. Check for loose joints. Use good 2-core cable.
Phone far away works poorly Check the cable run and joints. CCL specifies under 600 ohms loop resistance per extension.

Safety

  • Install indoors, in a dry, ventilated place.
  • Keep telephone cable away from mains wiring.
  • Do not connect batteries unless your model supports them.
  • Have a trained electrician do the wiring.

Manuals, videos and product page

CCL EPABX Range Brochure

Copper Connection PBX range, features and models.

Open PDF
Video guides

Installation and setup videos for NavKar products.

Watch on YouTube
Combo-CN134 product page

Specifications, photos and accessories.

View product

Still need help?

Warranty terms are as stated on your bill and on the product page. Keep your bill safe; we need it for any warranty claim. Free technical support is available for installation and setup.

Send us your model, purchase date and a photo or short video of the problem. WhatsApp +91 91384 68548, Mon–Sat 10:00–5:30.

Chat on WhatsAppAll manuals