Hikvision DS-K1T343EWX Face Attendance – Setup Guide
Setup guide · DS-K1T343EWX
Mount, connect and enrol staff on the Hikvision DS-K1T343EWX face recognition terminal. Use it for attendance, door access, or both.

What’s in the box
- DS-K1T343EWX face recognition terminal
- 12 V DC 1 A power adapter
Tools you’ll need
- Drill and wall plugs with screws
- Screwdriver
- LAN cable (or your Wi-Fi name and password)
- Power socket near the terminal
- Phone or PC for software, optional
Install
- Pick the spot.Indoors, beside the door, at a comfortable face height. Avoid direct sunlight or a bright window behind the person.
- Fix the mount.Mark the holes, drill and fix the wall mount as shown in the Quick Start Guide. Or use a base mount on a desk.
- Run the cables.Bring power, LAN and any door cables to the back of the terminal.
- Wire the door (optional).Connect an EM lock or drop bolt to the lock output, an exit switch to the exit input, and a door sensor to the door contact input. Follow the wiring label on the terminal and the Quick Start Guide.
- Fit the terminal.Fit it onto its mount and secure it as shown in the Quick Start Guide.
- Power on.Plug in the 12 V adapter. Connect the LAN cable, or set up Wi-Fi in the next step.
First-time setup
Activate and set up
- On first start, the screen asks you to activate the device. Create a strong admin password and keep it safe.
- Set the language, date and time.
- Set the network: plug in LAN, or join your Wi-Fi from the network settings.
Add staff
- Open User management and add a new user with an employee ID and name.
- Add the face: the person looks straight at the screen, 0.3 to 1.5 m away, in good light.
- Optional: add a 125 kHz EM card by holding it on the reader.
- Save. Repeat for each person. The terminal stores up to 1,500 faces and 3,000 cards.
Daily use
- Stand in front of the screen. Recognition takes under 0.2 seconds.
- Or hold a registered EM card on the reader.
- If a door is wired, it unlocks after a successful match. Press the exit button to leave.
- Download reports from the software at the end of the day or month.
Troubleshooting
| Problem | Try this |
|---|---|
| Face not recognised | Stand 0.3 to 1.5 m away, face the screen and remove a mask or cap. Re-enrol the face in good, even light. |
| Card not read | Only 125 kHz EM cards and fobs work. Mifare 13.56 MHz cards are not supported. Add the card to the user first. |
| Door does not open | Check the lock wiring to the lock output and the lock’s power supply. Check the door settings in the menu. |
| No network | Check the LAN cable and router. For Wi-Fi, check the name and password and keep the terminal within range. |
| Wrong time on punches | Set the date and time, or enable time sync over the network. |
| Forgot admin password | Contact us on WhatsApp with the device serial number. Do not try random passwords. |
Safety
- Use the supplied 12 V adapter only.
- Switch off power before wiring a lock or sensor.
- Indoor use only. Keep it away from water and direct sun.
- An EM lock releases when power fails. Plan a safe exit for every door.
- Keep the admin password private.
Manuals, videos and product page
Installation and setup videos for NavKar products.
Watch on YouTubeSpecifications, photos and accessories.
View productStill need help?
Warranty terms are as stated on your bill and on the product page. Keep your bill safe; we need it for any warranty claim. Free technical support is available for setup.
Send us your model, purchase date and a photo or short video of the problem. WhatsApp +91 91384 68548, Mon–Sat 10:00–5:30.
Chat on WhatsAppAll manuals