eSSL SilkBio-101TC Attendance – Setup Guide

Setup guide · SilkBio-101TC

Mount the eSSL SilkBio-101TC, enrol staff by face, fingerprint or card, and download attendance reports.

eSSL SilkBio-101TC face and fingerprint attendance machine

What’s in the box

  • SilkBio-101TC terminal
  • Accessories as per the packing list in your box
The device needs a DC 12 V, 1.5 A supply. Check the packing list in your box for the adapter and mounting parts.

Tools you’ll need

  • Drill, wall plugs and screws
  • Screwdriver
  • Power socket near the device
  • LAN cable or USB pen drive for reports
  • PC with eSSL attendance software, optional

Install

  1. Pick the spot.Indoors, at chest-to-face height, near the entry. Avoid direct sunlight on the screen and sensor.
  2. Fix the mount.Mark the holes, drill and fix the wall mount as shown in the eSSL manual.
  3. Connect cables.Bring the power cable and, if used, the LAN cable to the back of the device.
  4. Wire the door (optional).For access control, connect the lock and exit button as shown in the eSSL manual for your unit.
  5. Fit the device.Fit it onto its mount and secure it as shown in the manual.
  6. Power on.Plug in the 12 V adapter. The built-in 2000 mAh battery keeps it running for a while during short power cuts.

First-time setup

Date, admin and staff

  1. Open the menu and set the date, time and language.
  2. Create an administrator first, so only you can open the menu.
  3. Add each employee: User Mgt → New User. Enter a user ID (up to 9 digits) and name.
  4. Enrol the face: the person looks at the screen and follows the on-screen frame.
  5. Enrol fingerprints: press the same finger three times when asked. Add a backup finger.
  6. Optional: enrol an ID card or a password.
Capacity: 2,000 faces, 3,000 fingerprints, 3,000 cards and 100,000 records.

Reports

  1. For a USB report, insert a pen drive and use the download option in the menu.
  2. For network use, set the device IP in the communication menu and add it in eSSL’s attendance software on your PC.
  3. Open the report in Excel or as PDF.

Daily use

  1. Stand in front of the device for face, or place a registered finger on the sensor.
  2. Wait for the confirmation on screen before walking away.
  3. Check-in and check-out status can switch automatically by time. Set this up in the menu.
  4. Download reports weekly or monthly.

Troubleshooting

Problem Try this
Face not recognised Stand straight in front, remove a cap or mask, and re-enrol in normal room light.
Fingerprint fails Clean the sensor. Use the centre of the finger. Re-enrol with a different finger for dry or worn skin.
Device not found by software Check the LAN cable, IP address and that the PC is on the same network.
Wrong punch times Set the correct date and time in the menu. Check DST is off unless you need it.
Screen stays off The infrared sensor wakes the screen when someone approaches. Check the adapter if it never wakes.
Menu locked, admin forgotten Contact us on WhatsApp with the device serial number.

Safety

  • Use the 12 V DC adapter supplied or one of the same rating.
  • Indoor use only, 0 to 45 °C, 20 to 80% humidity.
  • Switch off before wiring a lock.
  • Always create an administrator so the menu is protected.

Manuals, videos and product page

eSSL SilkBio-101TC Brochure

Specifications from eSSL.

Open PDF
Video guides

Installation and setup videos for NavKar products.

Watch on YouTube
SilkBio-101TC product page

Specifications, photos and accessories.

View product

Still need help?

Warranty terms are as stated on your bill and on the product page. Keep your bill safe; we need it for any warranty claim. Free technical support is available for installation and setup.

Send us your model, purchase date and a photo or short video of the problem. WhatsApp +91 91384 68548, Mon–Sat 10:00–5:30.

Chat on WhatsAppAll manuals