ABT-250 Triple Beam Sensor – Setup Guide

Setup guide · ABT-250

Mount the ABT-250 transmitter and receiver, wire power and alarm, align the three beams and set the response time.

ABT-250 triple beam infrared sensor transmitter and receiver

What’s in the box

  • Infrared transmitter unit
  • Infrared receiver unit
  • Mounting brackets / base plates
  • Mounting screws and hardware
  • Installation guide
A power adapter is not included. Arrange a DC power supply within the rating on the label (the listing gives DC 10.5–30 V; the manual specifies DC 24 V).

Tools you’ll need

  • Drill and wall plugs, or pole clamps
  • Screwdriver set
  • Multi-core cable for power, alarm and tamper
  • DC power supply
  • Alarm panel or siren with an NO/NC input
  • Multimeter, helpful

Install

  1. Pick the line.Mount transmitter and receiver facing each other with a clear line of sight. No trees, plants or poles in between. Stay within the range on your unit’s label.
  2. Avoid sunlight.Do not let direct sun or strong lights shine into the receiver.
  3. Open the covers.Loosen the cover screw and remove the cover from both units.
  4. Mark and drill.Use the template to mark the holes on the wall or pole. Drill them.
  5. Pass the cable.Feed the cable through the wiring hole before fixing the body.
  6. Fix both units.Screw them firmly so they cannot move after alignment. For a pole, fix the base plate to the bracket first.
  7. Wire power.Power off. Connect DC power to terminals 1–2 on both the transmitter and the receiver.
  8. Wire the alarm.On the receiver, connect your alarm panel to COM + NC or COM + NO, as your panel needs. Connect the tamper terminals to the panel’s tamper input.
Do not exceed the rated voltage. Follow the terminal diagram printed inside the cover.

Align and test

Align the beams

  1. Power on both units.
  2. Look through the viewfinder on the receiver and turn the horizontal knob (about ±90°) to aim at the transmitter.
  3. Fine-tune with the vertical screw (about ±10°).
  4. Watch the signal-level LEDs. Adjust until you get the strongest, steady signal.
  5. Repeat on the transmitter side for best results.

Set the response time

  1. Choose the receiver’s response setting (about 50–700 ms) for the movement you want to detect: from high speed to slow walking.
  2. Set it shorter than the time an intruder takes to cross the beams.
  3. Close both covers.
  4. Walk through the beams. Confirm the receiver alarms and your panel or siren triggers.
The alarm triggers only when all three beams are blocked together. Birds and leaves blocking one beam do not trigger it.

Daily use

  1. Arm your alarm panel. The beams guard the line between the two units.
  2. Walk-test the beams every month.
  3. Keep the path clear of plants and objects.
  4. Wipe the covers clean after dust storms or heavy rain, then check the signal LEDs.

Troubleshooting

Problem Try this
Transmitter or receiver LED off Check the power supply voltage, polarity and terminals 1–2.
No alarm when beams are blocked Re-align both units. Check all three beams are received. Check the response-time setting.
Constant alarm Re-align. Remove plants or objects in the path. Check the covers are fitted properly.
Random false alarms Check for swaying plants, unstable mounting, loose wiring or an unstable power supply.
Weak signal Fine-tune horizontal and vertical alignment using the signal-level LEDs. Shield the receiver from strong light.
Panel gets no alarm Check COM, NO and NC wiring and that your panel input matches the contact type.

Safety

  • Switch off power before wiring.
  • Do not exceed the rated voltage or relay current.
  • Mount firmly so wind cannot move the units out of line.
  • Re-check alignment after storms.

Manuals, videos and product page

Video guides

Installation and setup videos for NavKar products.

Watch on YouTube
ABT-250 product page

Specifications, photos and accessories.

View product

Still need help?

1 year warranty.

Send us your model, purchase date and a photo or short video of the problem. WhatsApp +91 91384 68548, Mon–Sat 10:00–5:30.

Chat on WhatsAppAll manuals