Combo-CN111 Wi-Fi Rim Lock (Smart Life) – Setup Guide

Setup guide · Combo-CN111

Fit the RML-8K rim lock, wire the PSWF-01 Wi-Fi lock supply, pair your remotes and connect the Smart Life app. Open your gate by remote, phone or voice.

Combo-CN111 Wi-Fi rim lock with Smart Life app

What’s in the box

  • RML-8K electronic rim lock with strike
  • Key cylinder, 8 keys, ring, plate and screws
  • PSWF-01 Wi-Fi lock supply
  • 3 × RM-BR0243 brown remotes
Not included: exit switch, video door phone, cable and installation.

Tools you’ll need

  • Drill with metal bits
  • Screwdriver set
  • Welding machine, if a mounting plate is needed
  • 2-core cable from lock to supply
  • Smartphone with the Smart Life app
  • 2.4 GHz home Wi-Fi name and password

Install

Have a trained electrician do the wiring. Mounting on a metal gate may need a welded plate.

  1. Fit the rim lock.Mount it on the inside face of your metal gate or door. Pass the key cylinder through from outside. Fix the strike on the frame.
  2. Test by hand.Close the gate. The latch must drop into the strike cleanly and lock by itself.
  3. Mount the supply.Fix the PSWF-01 indoors on a dry wall, away from water and heat, within good Wi-Fi range.
  4. Switch off mains.Make sure the AC supply is off before wiring.
  5. Connect the lock.Run the two lock wires to the LOCK terminals (12 V DC output).
  6. Add extras (optional).Exit switch (normally open push button) to SW. Video door phone lock output to -VDP+ : minus to minus, plus to plus.
  7. Connect mains last.Wire AC 230 V, 50 Hz to the AC input only after all other wiring is done.
Follow the wiring diagram in the RML-8K manual (PDF below) exactly, or hand it to your electrician.

Pair remotes and the Smart Life app

Pair a remote

  1. Press ADD on the supply once.
  2. Press any key on the remote. The LED blinks to confirm.
  3. Repeat for each remote. You can pair up to 20.

Connect the Smart Life app

  1. Install Smart Life (Tuya) from the Play Store or App Store and create an account.
  2. Connect your phone to your 2.4 GHz Wi-Fi. 5 GHz is not supported. If your router shows two networks, pick the 2.4 GHz one.
  3. In the app, tap + to add a device.
  4. Press the WIFI pinhole button on the back of the supply to put it in pairing mode.
  5. Choose your 2.4 GHz Wi-Fi, enter the password and wait for the device to be added.
  6. Open the device, tap Timer, then Inching. Set it to 1 second and keep it ON.
  7. Tap the switch in the app. The gate should open.
Inching at 1 second is essential: it turns the lock off right after opening and protects the lock coil. Add up to 15 family members in the app, and link Smart Life to Alexa or Google Home to open by voice.

Daily use

  1. Press any remote once, tap the switch in Smart Life, or ask Alexa or Google Home.
  2. The latch locks again by itself as the gate closes.
  3. Remotes, the exit switch and the key work even without internet.
  4. In a power cut, open the gate from outside with the key.
  5. Press the remote or exit button once, briefly. The lock coil is made for a short pulse. Holding the button too long overheats and burns the coil.

Troubleshooting

Problem Try this
App cannot find the device Use 2.4 GHz Wi-Fi only. Keep the phone near the supply. Press the WIFI pinhole button again and retry.
Device shows offline Check the router is on and the supply has power. Move the router closer or add a Wi-Fi extender.
Remote does not work Replace the remote battery. Pair it again with ADD. Remotes work without internet.
Lock clicks but gate stays shut The latch is under pressure. Push or pull the gate slightly while opening. Re-align the strike.
Lock gets hot or stopped working Check Inching is ON at 1 second. A burnt coil from long presses is not covered by warranty.
Exit switch does nothing It must be a normally open (NO) button wired to SW.

Safety

  • Complete all wiring before connecting AC 230 V.
  • Mount the supply indoors only. Water, rain or moisture damage is not covered.
  • Keep Inching at 1 second. Never hold remote or exit buttons down.
  • Keep a key outside the house for emergencies.

Manuals, videos and product page

RML-8K Rim Lock Catalogue & Manual

Installation, wiring, remote pairing and troubleshooting for RML-8K lock kits. 21 pages.

Open PDF
Video guides

Installation and setup videos for NavKar products.

Watch on YouTube
Combo-CN111 product page

Specifications, photos and accessories.

View product

Still need help?

1 year warranty from the date of purchase, with the bill. Not covered: lock coil burnt from long presses, and water or physical damage to the power supply.

Send us your model, purchase date and a photo or short video of the problem. WhatsApp +91 91384 68548, Mon–Sat 10:00–5:30.

Chat on WhatsAppAll manuals